Ready to use in less than a minute, no assembly requiredĬomes with 4 suction cups and 4 adhesive strips attachedĮasy to attach. Tough & sturdy black plastic will not discolor, deform or breakĬurved smooth contour design that is gentle to touch 100 percent satisfaction guaranteed.Īccomodates all EZ Pass old & new mini and EZPass Flexįits all I-Pass, Palpass and i-Zoom transpondersĬompact design with suction cups behind toll tagĮasily tucked behind rearview mirror for safe driving Easy to transfer to another vehicle or remove and hide for theft prevention. Easily removed by pulling on suction cup tab or by sliding a small card under the cups. Easy to attach to windshield, simply push it into desired location on windshield. Will not rattle, discolor, melt or break. It attaches firmly in seconds without adhesives or hook-and-loop strips. Comes with four 3M dual-lock strips installed to mate with the two strips already installed on your toll pass. EZ Pass Holder for Windshield, Suction Cup iPass Transponder Toll Pass Holder BREEZE THROUGH TOLL PLAZAS with your EZPass or iPass affixed to your windshield in our transponder holder for car and truck. Uses 4 industrial grade suction cups for stability, and easily replaced if ever needed so you only buy this holder once. Compact design (3.90 by 3.5 inches) will not extend beyond your electronic toll tag, and can be hidden behind rearview mirror and out of your driving line of sight for safe driving. Made from tough clear plastic to withstand extreme heat and cold conditions. This EZ pass holder fit the old and new mini EZPass and EZPass Flex, I-Pass, I-Zoom, and Palpass transponders. Most Compact & Sturdiest Electronic Toll Tag Holder Please contact the dealership where you purchased your car to see if your vehicle contains any of these features.Four Suction Cup Toll Pass Holder Fits All EZ Pass & I-Pass transponders. Also, the following glass features may interfere with the E-ZPass signal and require alternative or exterior mounting: solar ray, solar tint, heated, heat reflected, insulated, Insta-Clear. In general, windshields that contain metal in the glass (metal oxide) and mirrors with compass or temperature readings may prevent the E-ZPass signal from being read properly.
#Ezpass izoom license#
Some vehicles have special features that require an exterior License Plate Tag (LPT) or alternative placement. Mounting for Vehicles with Special Windshield Features Please note: Your E-ZPass license plate tag should be attached to the center of the front bumper, even if your license plate is in a different location.Tighten the bolts securely, but do not over tighten. Fasten your E-ZPass tag to the front license plate using the existing top mounting bolts and the knock-out holes at the bottom of the E-ZPass tag, so you do not cover the state name on your license plate.This side should face inward to your vehicle. It will have the sticker with the Maine Turnpike Logo. Identify the flat side of your E-ZPass tag.You may order additional mounting strips by calling E-ZPass Customer Service atġ-888-MTA-PASS (1-88), Mon-Fri, 8 AM-6 PM
An extra set of mounting strips was provided with your E-ZPass order. Please note: Do not try to remove the mounting strips from your windshield and reuse them.Your E-ZPass tag may be removed by gently lifting one corner of the tag to separate the adhesive strips.Place the tag in the correct position and press firmly against the glass for 15 seconds to achieve a good bond. Turn the tag right side up facing you.Without removing the second set of adhesive strips from the tag, carefully remove the protective backing from the mounting strips on the rear of the tag. There are four adhesive strips: two are permanently mounted to the tag, and two are for mounting to the windshield.If your vehicle has tinted glass, make sure the device is at least 1 inch below the tinted section of glass. Locate the correct position for the tag - the upper center portion of your windshield behind the rearview mirror, at least 1 inch to the right of the mirror and at least 1 inch below the top edge of the windshield.This side faces the interior of the vehicle with the arrows on the tag pointing toward the roof.
#Ezpass izoom serial#
Identify the front face of your E-ZPass tag (it will have the label with the Maine Turnpike Logo and the tag serial number).Clean and dry the inside of your windshield around the rearview mirror.Vehicles with Special Windshield features.Standard windshield and license plate mounts.
0 kommentar(er)
